QuestPro接口
當QuestPro（用于辨識的過程測試數據生成器）可用時，若QuestPro應用于控制器，控制視圖上將顯示以下參數。
可以使用“Client Window Builder（客戶端窗口構建器）”配置顯示位置。默認值是控制面板的最后一列。
顯示條件如下：
1）若有任一使用QuestPro的控制器，并且任務狀態不為OFF。
2）QuestPro啟動后顯示以下參數。
3）所有任務狀態變?yōu)镺FF后，以下參數將不顯示。
表B 5.2控制視圖
|條目 |描述| 操作員 | 工程師|
| ------------- |:-------------:| -----:|
|Quest Status（Quest狀態）| 顯示QuestPro狀態。 0:OFF 1:STANDBY 2:ACTIVE 3:CONTROL 4. ******: QuestPro不應用。| R |R|
|Quest WDG timer (sec)計時器| QuestPro應用的Watch dog 計時器。 默認視圖為不顯示。請使用Client Window Builder（客戶端窗口構建器）定義它。| R |R|
|Current EF filter time constant（當前EF濾波器時間常數）| EF濾波器的傾斜時間常數。QuestPro可通過多次更改EF濾波器來移動POV和MV。 默認視圖為不顯示。請使用Client Window Builder（客戶端窗口構建器）定義它。| R |R|
|Original EF filter time constant（原始EF濾波器時間常數） |連接QuetPro之前的EF濾波器時間常數。| R |R|
為了改變MV和POV的動態行為，在優化模式下QuestPro將更改EF時間常數。
子控制器
| 條目| 描述| 操作員 | 工程師|
| ------------- |:-------------:| -----:|
| Sub Controller（子控制器）| Exasmoc子控制器的唯一Tag名。 | R| R|
| Actual Status（實際狀態） | 當前控制狀態。| R | R|
| Desired Status（期望狀態）| 在此條目的組合框幫助下，可以選擇/更改各個子控制器的狀態。 單擊組合框。 將顯示刪除菜單。 ACTIVE INACTIVE 如下所述，為子控制器操作選擇一種模式。 ACTIVE :根據主控制器的實際狀態計算控制動作并輸出到過程/HMI。 INACTIVE : 僅執行模型更新觀察。不計算控制動作。| R/W R/W | R/W R/W|
| Comment（評論）| 控制器評論 (16字符)。| R | R|
CALC計算
| 條目| 描述 | 操作員模式 | 工程師模式|
| ------------- |:-------------:| -----:|
| Sub Controller（子控制器） | 定義了計算后，“CALC”將顯示在樹狀圖中，分別定義了計算的次數。| R | R|
| Actual Status（實際狀態）| 當前控制狀態。| R | R|
| Desired Status（所需狀態）| 可以選擇計算狀態。 僅在ENG模式下可選擇。 ACTIVE INACTIVE ACTIVE:執行計算，且結果顯示在屏幕上。 當DCS位號名被定義為輸出地址時，計算結果將發送到DCS。 INACTIVE:執行計算，但不顯示在屏幕上或輸出到DCS。 在MC/SC概述面板上,將保留以前計算的值。| R | R/W|
| Comment（評論）| 控制器評論 (16字符)。| R | R|
原文：
QuestPro interface
When QuestPro (Process test data generator for identification) is available, the following parameters are displayed on the control view when QuestPro is applied to the controller.
The display location can be configurable using ‘Client Window Builder’. Default is the last column of the control panel.
The display conditions are as follows:
- There exists any controller which uses QuestPro.and the Quest status is not OFF.
- The below parameters are displayed after QuestPro starts.
- The below parameters become undisplayed after all Quest status become OFF.
Table B 5.2 Control view
| Item | Description | Operator | Engineer|
| ------------- |:-------------:| -----:|
| Quest Status| QuestPro status is shown. 0:OFF 1:STANDBY 2:ACTIVE 3:CONTROL 4. ******: QuestPro is not applied. |R| R|
|Quest WDG timer (sec)| Watch dog timer for QuestPro application. Default view does not display it. Please define it using Client Window Builder. |R |R|
|Current EF filter time constant| EF filter tilter time constant. QuestPro changes EF filter several times to move POV and MV. Default view does not display it. Please define it using Client Window Builder.| R |R|
|Original EF filter time constant |EF filter time constant before QuetPro is connected. | R |R|
In order to move MV and POV dynamic behavior, QuestPro changes EF time constant in the Optimise mode.
Sub Controller
|Item |Description | Operator | Engineer|
| ------------- |:-------------:| -----:|
|Sub Controller |Exasmoc Sub Controllerˇs unique Tag Name | R | R|
|Actual Status |Current control Status| R | R|
|Desired Status|With the help of Combo box under this item individual sub-controllerˇs Status can be selected/changed. Click Combo box. Drop out menu will appear. ACTIVE INACTIVE Select one of the modes for sub-controllerˇs action as described below. ACTIVE : Control actions are computed and output to the process/HMI according to the actual status of the main controller. INACTIVE : Only observation is performed for model updating. No control actions are computed.| R/W R/W |R/W R/W|
|Comment| Controllerˇs Comments (16 Characters) |R |R|
CALC calculation
|Item | Description| Operator mode |Engineer mode|
| ------------- |:-------------:| -----:|
|Sub Controller |When the calculation is defined, “CALC” is displayed on the tree view, in respective of the number of defined calculations.| R |R|
|Actual Status |Current control Status | R |R|
|Desired Status| Calculation status can be selected. Selection is available on ENG mode. ACTIVE INACTIVE ACTIVE Calculation is executed and the result is displayed on the screen. When the DCS tag name is defined as output address, the calculation result is sent to DCS. INACTIVE Calculation is executed, but the result is not displayed on the screen nor output to DCS. On the MC/SC overview panel, the previously calculated value remains.| R| R/W|
|Comment |Controllerˇs Comments (16 Characters) |R |R|
2017.1.4
