提示
- High Limit 應該 >= Low Limit；
- SETRANGE LOW≤SETRANGE HIGH
- SETPOINT LOW ≤ SETPOINT HIGH
- SETRANGE LOW≥SETPOINT LOW
- SETRANGE HIGH ≤ SETPOINT HIGH
如果SET VALUE TYPE（設定值類型）是SET PNT，則只有“SET RANGE HIGH”可編輯，且“SET RANGE HIGH”的值自動復制到“SET RANGE LOW”。
從R3.06起，CV設定范圍有四種類型，Set Range – Zone Control（設定范圍-區域控制），Set Point – Setpoint Control（設定點-設定點控制），Low Limit Zone Control（低限區域控制），在CV上只有下限（無上限）和High Limit Zone control（高限區域控制）只有高限（無低限）。在DEF文件中為每個CV定義了SETVALUETYPE。
即使為每個限制分配了位號名，也會執行上述錯誤檢查。檢測到錯誤時，數據變?yōu)锽ad。（R4.02）
**為了將Online Tuning Weight（在線整定權重）反映到控制器，應從控制面板觸發在線整定。然后在下一個執行周期得到修改。
B12經濟函數視圖
Economic Function (EF)（經濟函數）參數顯示在Economic Function（經濟函數）面板上。可以在PCTP離線定義多個經濟函數。在此面板上，操作員可以選擇經濟函數并輸入控制器的EF參數。
經濟函數面板有“ENG”和“OPE”兩種操作模式。以下是ENG模式的窗口。
查看
條目說明
各個需要由操作員和工程師輸入的條目/參數如下。
|條目| 描述 |操作員模式| 工程師模式|
| ------------- |:-------------:| -----:|
|Common（通用）|
|Tracking Filter（跟蹤濾波） |確定跟蹤濾波常數。非負值為可用的，單位是秒。| R |R/W|
|Economic Function Value（經濟函數值） | 所選經濟函數的計算值。| R| R|
|Optimal Value（最優值）| 表示EF在優化期間實現的最佳可能值。為穩態計算值（預測時域終點）。| R |R|
|Economic Function Selection(經濟函數選擇) |表示所選的經濟函數條目。| R| R|
|Status（狀態）| 指示所選經濟函數的狀態。 ACTIVE INACTIVE BAD |R |R|
|EF Common（EF通用）|
|Economic Function Selection(經濟函數選擇) |表示所選的經濟函數的條目。| R/W |R/W|
|Function Name（函數名）| 經濟函數的唯一位號名。 |R| R|
|Comments（注釋）| EF位號注釋。| R| R|
|Economic Coefficients(經濟系數)|
|Coefficient Name(系數名)| 經濟系數的唯一位號名。| R| R|
|Comment（注釋） |經濟系數注釋。| R| R|
|Value （值） |經濟系數值(Z_Coefficient)。| R/W |R/W|
|Button（按鈕）|
|Apply Button（應用按鈕）| 如前所述。| R/W |R/W|
|Undo Button(撤銷按鈕) |在單擊Apply按鈕之前取消新輸入的參數。然后上一個參數顯示為黑色。| R/W |R/W|
原文：
TIPS
- High Limit should be >= Low Limit
- SETRANGE LOW≤SETRANGE HIGH
- SETPOINT LOW ≤ SETPOINT HIGH
- SETRANGE LOW≥SETPOINT LOW
- SETRANGE HIGH ≤ SETPOINT HIGH
If the “SET VALUE TYPE is SET PNT then only “SET RANGE HIGH” is editable and value of “SET RANGE HIGH” is copied to “SET RANGE LOW” automatically.
From R3.06, there are 4 type of CV set range, Set Range – Zone Control, Set Point – Setpoint Control, Low Limit Zone Control with only low limit (no high limit) on CV, and High Limit Zone control with only high limit (no low limit) on CV. SETVALUETYPE is defined in the DEF file for each CV.
The above error check is also done even when the tag name is assigned to each limit. The data becomes Bad when the error is detected. (R4.02)
** In order to reflect Online Tuning Weight to the controller, Online tuning should be triggered from the control panel. Then the modification is reflected at the next execution period.
B12. Economic Function View
Parameters of Economic Function (EF) are displayed on the Economic Function Panel. Multiple Economic functions can be defined on PCTP offline. On this panel, operators can select the economic function and enters the EF parameters for the controller.
Economic Function Panel has two modes of operation, “ENG” and “OPE”. Following are the windows for the ENG modes.
View
Description of items
Various items/parameters need to be entered by operator and engineers are described below.
| Item| Description | Operator mode| Engineer mode|
| ------------- |:-------------:| -----:|
| Common|
| Tracking Filter | Determines the Tracking Filter Constant. Non-negative value is available. Unit is second.| R | R/W|
| Economic Function Value| Calculated value of the selected Economic Function. | R| R|
| Optimal Value| Value indicates the EF’s best possible value to achieve during optimization. Value is calculated for steady state (end of the prediction Horizon)| R| R|
| Economic Function Selection| Indicates the selected Economic Function Index.| R | R|
| Status | Indicates the status of the selected economic function. ACTIVE INACTIVE BAD| R| R|
| EF Common|
| Economic Function Selection | Indicates the selected Economic Function Index. | R/W| R/W|
| Function Name | Unique Tag Name of the Economic Function| R | R|
| Comments | EF Tag comments| R | R|
| Economic Coefficients|
| Coefficient Name| Unique Tag Name of Economic Coefficient| R | R|
| Comment Economic Coefficient Comments| R | R|
| Value | Economic Coefficient Value (Z_Coefficient) | R/W| R/W|
| Button|
| Apply Button| As Explained Earlier| R/W| R/W|
| Undo Button| Cancel a newly entered parameter before the “Apply” button is clicked. Then previous parameter is displayed in black. | R/W| R/W|
2017.1.8
